At the conclusion of this auction, the credit card you used to register with will automatically be charged for your purchases. International bidders, please see last paragraph below. A PAID invoice will be emailed to you. Please be sure that the card you used to register has sufficient funds/credit limit available. If you do not receive this email by Friday morning, please check your SPAM folder. You can always email or call the auction company and have us resend the email to you. INTERNATIONAL BIDDERS, unless you are an established customer, a bank wire transfer will be required for all purchases over $100 USD. Please contact auction company for wire transfer information.

Bidding is really simple, particularly if you've bid in an online auction before, but here's a quick rundown on some features that may be unfamiliar: Each lot in the auction is scheduled to close approximately 20 seconds apart. For example, Lot 1 is scheduled to close at 7:00.00 pm central time. Lot 2 is scheduled to close at 7:00:20, Lot 3 is scheduled to close at 7:00:40, Lot 4 is scheduled to close at 7:01:00. Soft Close--- The auction software has a "soft close" feature so that if a lot is bid on in the final three minutes before that particular lot is scheduled to close, that lot extends for another three minutes. For example, say Lot 10 has one minute left before it closes and a bid is placed on it: Lot 10's time will extend to four minutes. Then if Lot 10 ticks back down to two minutes remaining and another bid is placed, then Lot 10 will extend to five minutes. As long as active bidding is occurring in that final three minute window, it will keep extending that lot's time. This does not affect any other lots in the auction, just that particular lot. This is the easiest way to emulate "live" auction bidding, and a very common practice in online auctions (not eBay). High bids and maximum bids--- Bidders can place maximum bids which remain secret; the system will only bid up to the competitive bids and show that number as the high bid. For example, if your maximum bid is $100 and the next highest bidder's maximum bid is $40, then you would be the high bidder at $41 (based on the bid increment table). If bids go past your maximum, you'll be notified by email that you've been outbid and can then bid again if you choose. If two bidders happen to have the same maximum bid, then the first bidder at that value is shown as the high bidder.

Previews and pickup will be located at: 404 NE 41st. St., BLDG 2 Kansas City, MO 64116 (commercial building behind home; look for the 50 ft. tower) Preview Date: Saturday, 8/31 from 9AM - Noon CT, by Appointment Only. Local Pickup Date: Pickup is scheduled for Saturday, 9/7 from Noon - 3PM CT.

IF SHIPPING IS REQUIRED, WE ADVISE YOU TO CONTACT OUR SHIPPER OR THE AUCTION COMPANY FOR A QUOTE PRIOR TO BIDDING. WEIGHTS AND DIMENSIONS OF EACH LOT ARE INCLUDED IN THE ITEM DESCRIPTION. WE DO NOT SET SHIPPING/PACKING CHARGES. THEIR INFORMATION AND OTHER RELATED INFO CAN BE FOUND AT THE LINK BELOW. PLEASE COPY AND PASTE IT INTO YOUR BROWER TO VIEW. https://www.schulmanauction.com/vintage-electronics/auction-shipping/

When possible, we do our best to test the equipment we sell so that you will know exactly what you are bidding on. That being said, we perform basic tests such as overall power consumption, receiver sensitivity, transmitter power output, etc. Depending on what it is we’re selling, other tests might be warranted. If there is a certain type of test you’d like performed on a particular lot, just let us know and we’ll do our best to take care of you. Please note that we do not usually go through every single function on a particular piece of gear (in some cases, that would take a considerable amount of time) but rather the functions that will tell us (and you) whether or not the piece of equipment your interested in, is in basic working order. Does it transmit? Does is receive? Does that piece of test gear you’re wanting to bid on do what it is supposed to do? All this with supporting data and photos when appropriate. For more information and specifics about our test bench, please cut and paste the following link into your browser: http://www.schulmanauction.com/vintage-electronics/test-bench-equip-testing/

Lunar Link Systems LA-22A 2M, 1.5 kW, VHF Linear Amplifier and PS-70D HV DC Power Supply. Includes CX-800N Coaxial Relay, 144M Dual Directional Coupler, and manuals. Scans of the complete manual for both the amp and power supply are provided in the links above. Please look through them if you are not familiar with this amplifier. Very nice 2M amp. This amp was primarily used for EME communications. Drive was approximately 40-50W, and power output was between 1,200 - 1,500W, as shown. (NOTE: ICOM radio and Diawa power meter not included). ****You will notice a switch on the back of the amp, under the fan, was added by the seller. When this amp was purchased, there was an option to run 2 amps with one power supply. In order to do this a jumper between E24-E25 on the amp had to be clipped. For convenience, the seller added the switch so he could use them in either a single or double configuration.***** Fan will be removed for shipping. Amp: 13x6x12 plus fan, 20 lbs, SN 23117 Power Supply: 8x14x9, 60 lbs, SN 25241

Lunar Link Systems LA-72A 440 MHz, 1.5 kW, UHF Linear Amplifier and PS-70D HV DC Power Supply, CX-800N Coaxial Relay, 432M Dual Directional Coupler, and manuals. Scans of the complete manual for both the amp and power supply are provided in the links above. Please look through them if you are not familiar with this amplifier. Very nice 440 MHz amp. This amp was primarily used for EME communications. Drive was approximately 40-50W, and power output was approximately 1,100W, as shown. (NOTE: ICOM radio is not included). ****You will notice a switch on the back of the amp, under the fan, was added by the seller. When this amp was purchased, there was an option to run 2 amps with one power supply. In order to do this a jumper between E24-E25 on the amp had to be clipped. For convenience, the seller added the switch so he could use them in either a single or double configuration.***** Fan will be removed for shipping. Amp: 13x6x12 plus fan, 20 lbs, SN 21146 Power Supply: 8x14x9, 60 lbs, SN 25250

Lunar Link Systems LA-62 6M, 1.5kW, VHF Linear Amp, CX-800N Coaxial Relay, 50M Dual Directional Coupler, and manual. A POWER SUPPLY IS NOT INCLUDED, see last paragraph below for options. Scans of the complete manual for the amp are provided in the link above. Please look through it if you are not familiar with this amplifier. Very nice 6M amp. This amp was primarily used for EME communications. Drive was approximately 40-50W, and power output was approximately 1,200W, as shown. ****You will notice a switch on the back of the amp, under the fan, was added by the seller. When this amp was purchased, there was an option to run 2 amps with one power supply. In order to do this a jumper between E24-E25 on the amp had to be clipped. For convenience, the seller added the switch so he could use them in either a single or double configuration.***** Fan will be removed for shipping. Power supplies for this amp are available from Steve Simons of Manitou Systems for $1,100. Their number is 203-733-2110. If you plan on building your own power supply for this amp, we do have the cables/connectors available and we'll send them along with the amp. Just respond to your end of auction email and let us know you'd like them sent. A PDF of the power supply manual and schematics can be found in LOTS 2 & 3 of this auction. SN 29039 13x6x12, 20 lbs

Lunar Link LA-12A 220 MHz VHF Linear Amplifier, with CX-800N Coaxial Relay, 220M Dual Directional Coupler, and manual. A POWER SUPPLY IS NOT INCLUDED, see last paragraph below for options. NOTE: There is a stain on the top of the amp and some of the black paint is blistered, as shown. Scans of the complete manual for the amp are provided in the link above. Please look through it if you are not familiar with this amplifier. Very nice 220 Mhz amp. This amp was primarily used for EME communications. Drive was approximately 40-50W, and power output was approximately 1,400-1,500W, as shown. ****You will notice a switch on the back of the amp, under the fan, was added by the seller. When this amp was purchased, there was an option to run 2 amps with one power supply. In order to do this a jumper between E24-E25 on the amp had to be clipped. For convenience, the seller added the switch so he could use them in either a single or double configuration.***** Fan will be removed for shipping. Power supplies for this amp are available from Steve Simons of Manitou Systems for $1,100. Their number is 203-733-2110. If you plan on building your own power supply for this amp, we do have the cables/connectors available and we'll send them along with the amp. Just respond to your end of auction email and let us know you'd like them sent. A PDF of the power supply manual and schematics can be found in LOTS 2 & 3 of this auction. SN 22041 13x6x12, 20 lbs

Yaesu FTDX5000MP Transceiver + SM-5000 Station Monitor, plus MD-100 Mic, cables for station monitor, manual and Nifty manual, as shown. There is a bit of wear, as you can see on the top right front area of the rig. With the exception of a dim display (which is a common issue with these radios, well documented online), it works like a champ. PLEASE NOTE: The video and photos make the display appear brighter than it actually is, and display is at max settings. In a dimly lit room, the display looks great. RX sensitivity is 0.1 uv on all bands and RX power output ranges from 200W to 190W on all bands. Very nice looking and sounding radio! Xcvr SN 2M500040 SM-5000 SN 2M050 17x18x6, 50 lbs

Icom IC-7610 HF/50 MHz Transceiver, with original box, manual, CD, hand mic, DC power cable and misc. fuses/connectors, as shown. Very nice rig, with bright display. All controls appear to work well, and TX power output is 97W - 100W on 160M through 10M, and 90W on 6M. RX sensitivity ranges from 0.1 to 0.2 uv on all bands. This radio is at v1.2 firmware and has been reset to factory defaults. SN 12001477 5x13x12, 19 lbs

Icom IC-7300 HF/50 MHz Transceiver in very good overall cosmetic condition, as shown. Includes hand mic, manual and CD. DC power cord included, but not shown. Display is bright and sharp, controls work well. TX power output ranges from 95W - 100W on 160M through 10M, and 90W on 6M. Unit has been reset to factory defaults and is currently at firmware version 1.3. SN 02005876 5x10x11, 14 lbs

Icom IC-9700 VHF/UHF/1.2 GHz D-Star Transceiver, with mic, power cord, manual, and original box. Bright, sharp display and all controls work as they should. TX power output was 75W on 2M, 65W on 440 MHz, and 5W - 10W on 1.2 GHz. PLEASE NOTE: the 1.2 GHz measurement accuracy is limited by our bench testing capabilities. RX sensitivity ranges from 0.1 to 0.2 uv on all bands. D-Star capabilities were not tested. SN 12003092 5x10x11, 11 lbs

Icom IC-910H VHF/UHF (& 1.2 GHz) Transceiver with hand mic, DC power cord and original box, as shown. Nice display, all controls work well. TX power output on 2M was 100W, 440 MHz, 40W and 1.2 GHz, 5W - 10W. PLEASE NOTE: the 1.2 GHz measurement accuracy is limited by our bench testing capabilities. RX sensitivity is 0.1 uv on all bands. SN 01725 16x12x7, 14 lbs

Icom IC-910H VHF/UHF Transceiver. This rig does not include the 1.2 GHz option. Nice diplay and controls all work well. You will need to supply your own DC power cord and mic for this radio. TX power output was 90W on 2M and 50W on 440 MHz. RX sensitivity is 0.1 uv on all bands. SN 02948 16x12x7, 14 lbs

Yaesu FT-991 HF/VHF/UHF Transceiver. This is NOT the "A" version. Included with this rig is a hand mic, DC power cord, documentation, Nifty manual and original box, as shown. The unit has been reset to factory defaults. Tuner works well and display is bright and sharp. TX power output is 95W - 100W on 160M through 10M, and 60W on 2M and 440 MHz. RX sensitivity is excellent at 0.1 uv on all bands. SN 6D270463 12x9x4 plus original box, 10 lbs

Yaesu FTM-400DR C4FM Fusion Transceiver, with manual, hand mic and DC power cord. Original box included, but not shown. Display is bright and sharp, all controls work well. TX power output is approximately 40W on both VHF/UHF and RX sensitivity is 0.1 uv on both bands. SN 5J300494 10x14x4 (box), 4 lbs

Yaesu FTM-7250D C4FM Fusion Transceiver in good cosmetic condition. Includes hand mic, mounting bracket, USB cable. Display is bright, controls work well. RX sensitivity less than 0.15uv. TX power output 40W and 50W on 2M and 440. SN 8F020055 4x10x14, 5 lbs

Yaesu FT-847 Transceiver. With original box (not shown), manual and DC power cord. PLEASE NOTE: You will see a jumper with a couple SMA connectors added to the back of this rig. This was added by the original owner to split RX/TX. For normal use, just leave them connected, as shown in the photos. The display is bright and sharp, and all controls work well. NOTE: The internal speaker is inoperable, so we used headphones for testing. RX sensitivity ranges from 0.1 to 0.2 uv depending on band. TX power output is 95W - 100W on 160M - 6M and 50W on 2M, and 60W on 440 MHz. SN 8J120340 12x11x4, 15 lbs

Kenwood TS-2000X HF/VHF/UHF & 1.2 GHz Transceiver. Includes hand mic, DC power cord, manual and original box. TX power output is 85W - 95W on 160M - 10M, 60W on 6M, and 50W on both 2M and 440 MHz. Output on 1.2 GHz was about 10W. PLEASE NOTE: the 1.2 GHz measurement accuracy is limited by our bench testing capabilities. RX sensitivity ranges from 0.2 to 0.4 uv on all bands. SN 60800001 15x11x4, 17 lbs

Yaesu VX-7R Quad Band HT Transceiver in overall good cosmetic condition, with accessories, as shown. Display is sharp, and controls and switches are in working order. Battery does hold a charge. The only issue we found was that it will only transmit at high power, even if the controls are set to low power. TX power output is 4W+ on 6M, 2M and 440 MHz. Slightly less than 1W on 220 MHz (as per spec). RX sensitivity is very good, at 0.2 uv on all bands. SN 7N021602 9x6x3, 4 lbs

Elecraft K3/100 Transceiver in overall very good cosmetic condition. You will need to supply your own DC power cord. Display is bright and sharp. All controls work well. The following options are installed, KPA3 power amp, KIO3 digital AF, and KAT1 antenna tuner. Note that "N" type RF connectors are used for ANT1 and ANT2. Firmware versions are: MCU v5.67; FPF v1.26; DSP v2.88. TX power output ranges from 105W on 160M to 95W on 6M. RX sensitivity is 0.15 uv on all bands. SN 00465 12x11x5, 10 lbs

Elecraft P3 Panadapter in very good working as well as cosmetic condition. This unit was tested with the K3 in the previous LOT. SN 2482 5x6x11, 5 lbs

AR TRS04VD Transmit/Receive Sequencer + DPDT Type-N, By-Pass Dow Key Relay, model 260-230142. See above link for information from the company's web page on the sequencer. It has been placed in a black project box, with RCA connectors, as shown. Basically, the relay goes on the top of the tower near the antenna. It is used to bypass the tower preamp. The sequencer in conjunction with a 25 volt power supply sends the relay coil voltage up two wires to the relay, just before the sequencer keys the power amplifier and then the exciter. This protects the preamp from damage. To complete your system, you can find various preamps in LOTS 24 through 28. These are working units. 2 lbs

AR TRS04VD Transmit/Receive Sequencer + DPDT Type-N, By-Pass Dow Key Relay, model 260-230142. See above link for information from the company's web page on the sequencer. It has been placed in a black project box, with RCA connectors, as shown. Basically, the relay goes on the top of the tower near the antenna. It is used to bypass the tower preamp. The sequencer in conjunction with a 25 volt power supply sends the relay coil voltage up two wires to the relay, just before the sequencer keys the power amplifier and then the exciter. This protects the preamp from damage. To complete your system, you can find various preamps in LOTS 24 through 28. These are working units. 2 lbs

AR TRS04VD Transmit/Receive Sequencer + DPDT Type-N, By-Pass Dow Key Relay, model 260-230142. See above link for information from the company's web page on the sequencer. It has been placed in a black project box, with RCA connectors, as shown. Basically, the relay goes on the top of the tower near the antenna. It is used to bypass the tower preamp. The sequencer in conjunction with a 25 volt power supply sends the relay coil voltage up two wires to the relay, just before the sequencer keys the power amplifier and then the exciter. This protects the preamp from damage. To complete your system, you can find various preamps in LOTS 24 through 28. These are working units. 2 lbs

AR TRS04VD Transmit/Receive Sequencer + DPDT Type-N, By-Pass Dow Key Relay, model 260-230142. See above link for information from the company's web page on the sequencer. It has been placed in a black project box, with RCA connectors, as shown. Basically, the relay goes on the top of the tower near the antenna. It is used to bypass the tower preamp. The sequencer in conjunction with a 25 volt power supply sends the relay coil voltage up two wires to the relay, just before the sequencer keys the power amplifier and then the exciter. This protects the preamp from damage. To complete your system, you can find various preamps in LOTS 24 through 28. These are working units. 2 lbs

Advanced Receiver Research P144VDG Preamp in good working condition. 1 lb

Advanced Receiver Research P432VDG Preamp, in good working condition. 1 lb

Down East Microwave L432LNA Preamp in good working condition. 1 lb

Down East Microwave L222LNA Preamp, in good working condition. 1 lb

Advanced Receiver Research P220VDG Preamp, in good working condition. 1 lb

Collins KWM-1 Transceiver, 516F-1 Power Supply, 312B-1 Speaker, and 189A-1 Phone Patch. All units are in overall good cosmetic condition with some paint chips and scratches, as shown. Power supply appears to work, with all voltages present. However, the transceiver does not RX/TX. The S meter is working. Speaker works, but speaker wire is broken at connector and will need to be replaced. The phone patch was not tested. With a bit of TLC, you can bring this complete station back to life...a great addition to your vintage Collins gear. Transceiver: SN 753, 14x1x7, 16 lbs Power supply: SN 224, 11x8x6, 27 lbs Speaker: 7x8x10, 10 lbs

Collins 75S-3B Receiver, WE, in good cosmetic condition. Includes power cord, and one 2.1 Kc mechanical filter. RX sensitivity less than 0.3 uv on all bands, except 28 Mhz, which is non-operational. SN 16368 15x13x8, 18 lbs

Collins 75S-3B Receiver, WE, with manual. In good cosmetic condition, but with no power cord. All functions work well but S meter is not accurate. Includes all 3 mechanical filters, as shown. RX sensitivity less than 0.3 uv on all bands. SN 16649 15x13x8, 18 lbs

Collins 75S-3 Receiver, WE, in good cosmetic condition. No power cord. All functions work properly. RX sensitivity is poor, about 10 to 100 uv on all bands. Could use a tune up/alignment. SN 14578 15x13x8, 18 lbs

Collins 75S-3 Receiver, WE, in good cosmetic condition. No power cord. All functions work well, and RX sensitivity is less than 0.3 uv on all bands. SN 14417 15x13x8, 18 lbs

Collins 75S-1 Receiver, WE, in good cosmetic condition. Includes power cord. All functions work, however, switches and controls are dirty, need some TLC. RX sensitivity less than 0.2 uv on all bands. SN 2109 15x13x8, 18 lbs

Collins 75S-1 Receiver, WE, in good cosmetic condition. Controls are dirty, pre-select needs some attention. RX sensitivity is poor, about 100.0 uv on all bands. No USB/CW RX, however, calibration tone works. SN 643 15x13x8, 18 lbs

Collins 32S-3 Transmitter, RE, in very good cosmetic condition, as shown. However, the unit has keying and carrier oscillator issues. No power output. Will need some work. 15x12x8, 17 lbs

Collins 32S-1 Transmitter, WE, in good cosmetic condition. No 10M crystal, modulation is OK. Has an unknown red toggle switch on the front panel, seems to be standby/op. TX output 60W at 15M, 64W on 20M, 53W on 40M, and 110W on 80M. No SN 15x12x8, 17 lbs

Collins 30L-1 Linear Amplifier, 120V. This amp is in good cosmetic condition, as shown. TX power output, with 80W of drive, ranges from 480W on 80M to 430W on 10M. 8x15x14, 39 lbs

Collins 30L-1 Linear Amplifier, WE, 120V. This amp is in overall good cosmetic condition, as shown. Power output with 80-90W of drive, ranged from 550W on 80M to 300W on 10M. 8x15x14, 39 lbs

Collins 30L-1 Linear Amplifier, WE, no cabinet, as shown. TX power output is as follows: 80M 100W in, 490W out 20M 95W in, 240W out 10M 75W in, 220W out 8x15x14, 39 lbs 8x15x14, 39 lbs

Collins 30L-1 Linear Amplifier, WE, no cabinet as shown. TX power output is as follows: 10M - 560W out, 72W in 20M 700W out, 85W in 80M 700W out, 90W in 8x15x14, 39 lbs

Collins 516E-1 Power Supply, as shown. 800V supply only measures 200V, and 275V & bias supply both OK. 6x11x7, 12 lbs

Modified Collins 516F-2 Power Supply Test points for a Hi/Lo B+ on front panel. Bias adjust pot on front, works well. All voltages present. Uses SS rectifiers. 12x10x8, 26 lbs

National HRO-5TA1 VLF/HF Receiver Set with Coil sets A - F and LF coils, matching MCS speaker, 697 power supply and manual. This set is in very good cosmetic as well as working condition. All functionality works, except the S meter is not accurate. RX sensitivity is less than 0.5 uv on all bands except for 10M where it is approximately 5.0 uv. Receiver 20x17x11; 55 lbs Power Supply 8x8x7; 13 lbs. MCS 8" Speaker; 10 lbs.

National SW-3 1930's "Thrill Box" Receiver. Very clean unit, as shown. Includes original manual. This unit does not include coils. 8x10x10, 11 lbs

Electronic Assistance Corp. R-390A/URR Receiver in overall very good cosmetic condition, as shown. RX sensitivity ranged from 0.2 to 0.4 uv depending on band. The switches and controls could use some cleaning as they are dirty/noisy. SN 112 19x17x10, 85 lbs

Palstar AT5K Antenna Tuner in very good cosmetic as well as working condition. Internal inspection is clean, with no arcing evident. Includes power brick. SN 11400 8x15x18, 20 lbs

Kenwood TS-690S Transceiver in good overall cosmetic condition. You will need to supply your own DC power cord and mic. The display is not very bright, but readable. Tuner works well as do the controls and switches. RX sensitivity is 0.1 to 0.2 uv depending on band, and TX power output is 110W on 80M - 15M, and 100W on 12/10M, and 50W on 6M. SN 50500300 19x15x8, 23 lbs

Kenwood TR-7400A Transceiver in good cosmetic condition. With DC power cord, but no mic. TX power out 8W on low, 30W high. RX sensitivity 0.19uv at 146 MHz. SN 750544 4x8x11, 7 lbs

Tokyo Hy-Power Labs HL-160V25 VHF RF Power Amplifier in good cosmetic condition. Very good working condition. Power output approximately 145W, with about 25W drive. Preamp works. 4x9x11, 5 lbs

Kenwood TL-922A Linear Amplifier in overall good to very good cosmetic condition. All controls and lamps are working. Idle current is 120 mA, plate voltage is 3200V SSB and 2100V CW. TX power output is as follows: 160M, 80W drive, 1000W output 80M, 80W drive, 1000W output 40M, 80W drive, 1100W output 20M, 80W drive, 1100W output 15M, 85W drive, 1050W output 10M, 90W drive, 750W output SN 4060072 8x16x17, 68 lbs

Heathkit SB-200 Linear Amplifier in good cosmetic condition, with manual. The power supply board was updated, as shown in the last photo. Idle current is 70 mA, plate voltage is 2200V. The meter lamp is out. TX power output is as follows: 80M, 100W drive, 400W output 40M, 100W drive, 375W output 20M, 100W drive, 341W output 15M, 100W drive, 270W output 10M, 30W drive, 100W output, however, there is a high input SWR on this band. 15x15x8, 50 lbs

Heathkit SB-200 Linear Amplifier, 120V. This amp is in overall good cosmetic condition. Note the added switch in the lower, middle part of the front panel. Unknown use. Idle current is 100 mA, plate voltage is 2500V. TX power output ranges from 395W on 80M with 95W of drive, to 220W on 10M, with 60W of drive. 15x15x8, 50 lbs

Heathkit SB-201 Linear Amplifier, 120V. This amp is in overall good condition, as shown. New DC filter board, and caps. Idle current is 90 mA, plate voltage is 2400V. The amp DOES NOT HAVE 10M. TX power output ranges from 585W on 80M to 210W on 15M, with 90-100W of drive. 15x15x8, 50 lbs

Drake MS-4 Speaker & AC-4 Power Supply, in good cosmetic condition. All voltages are present, and speaker works. 12x11x6, 24 lbs

Drake 2-AQ Q Multiplier, in working condition, but the tuning knob will need attention as it doesn't "adjust" as the shaft is rotated. Controls could use cleaning. 8x7x8, 5 lbs

Drake 2-BQ Q Multiplier, in working condition. Controls could use cleaning. 8x7x8, 3 lbs

Drake 2-B Receiver in good overall cosmetic condition, however, the radio will need some work. No RX. Switch noise is heard when "Prod/Diode" switch is operated, but nothing else heard. AVC/S meter moves when Standby/RCV switch is operated, otherwise the unit is non-operational. 8x12x9, 16 lbs

Ten-Tec 1254 SSB-CW-AM Receiver Kit, unassembled, appears complete. As shown. 4 lbs

Icom IC-SP3 Speaker, in good cosmetic (a few scratches) and working condition. 11x14x7, 5 lbs

Heathkit SP-99 Station Speaker Kit. Unassembled, appears complete. As shown. 4 lbs

Four Motorola HSN431B Speakers, all in good and working condition. As shown. Mobile speakers. 4 lbs

Kenwood KA-9100 Stereo Integrated Amplifier in good overall cosmetic condition, as shown. Unit powers up and both meters work smoothly. Both channels produced rated power output with 0 dBv, 400 Hz and 1 kHz input. Some of the controls and switches will need cleaning. SN 730765 6x17x15, 38 lbs

Sherwood S-2200 Stereo Tuner in good overall cosmetic condition. Both AM/FM tuners as well as both tuning eyes work. Switches and controls will need cleaning and lubrication. 14x11x4, 21 lbs

Tascam 22-4 1/4 Inch 4-Channel Reel to Reel in overall good to very good cosmetic condition, as shown. That being said, the unit powers up, meters light, and amps and switches all appear to work. However, the capstan does not rotate properly, so some repairs or adjustments will be necessary. 17x16x10, 55 lbs

Astron RS-70M Power Supply in good cosmetic condition. Tested well under load. Includes power cord. 14x6x11, 55 lbs

Astron RS-70M Power Supply in good cosmetic condition. Includes power cord. Tested well under load. 14x6x11, 55 lbs

Astron RS-70M Power Supply in good cosmetic condition. Tested well under load. Includes power cord. 14x6x11, 55 lbs

Astron SS-30M Power Supply + attached RigRunner 4005 power panel. In good cosmetic condition. Power supply tested good under load, power strip works but has a blown 5 amp fuse. 10x8x3, 6 lbs

4005 Astron SS-30M Power Supply + attached RigRunner 4005 power panel in good cosmetic condition, as shown. Tested well under load, and RigRunner 4005 is in good working condition. 10x8x3, 6 lbs

4005 Astron SS-30M Power Supply + attached RigRunner 4005 power panel. In good cosmetic and working condition. Tested well under load. 10x8x3, 6 lbs

Astron RS-35M Power Supply in good cosmetic condition. Tested to full load and works well. 11x11x6, 24 lbs

Astron RS-35A Power Supply in good cosmetic condition. In good working condition. Tested well under full load. 11x11x6, 24 lbs

Astron RS-12A Power Supply in good working condition, tests well under load. 5x8x10, 15 lbs

Rigol DSA815 Spectrum Analyzer with tracking generator in very good cosmetic condition. This unit works to spec and includes direct coupler unit and power cord, as shown. 15x7x5, 11 lbs

Heathkit/Collins Station Monitor/Scope. Appears to have been an SB-610 or other similar chassis retrofitted in a Collins cabinet and modified front panel with a round emblem. All functions work and the CRT is bright! 7x10x11, 8 lbs

Racal-Dana 9908 Universal Counter Timer in good overall cosmetic as well as working condition. Display is bright and sharp, all digits and control switches work OK. Input controls work well. 4x14x12, 9 lbs

Tektronix 2235 Oscilloscope, with power cord (not shown). This 2 channel, 100 MHz scope is in good working condition. Bright display. No probes are included. 6x16x17, 15 lbs

Tektronix K212 Portable Instrument Cart, as shown. In good cosmetic condition, and works well. PLEASE NOTE: Shipping will be extremely expensive due to the oversize nature of this item. Please contact auction company if you would like a quote. If you do not contact us for a quote prior to bidding, and you are the winning bidder, we will not issue a refund if you decide you do not want this item due to high shipping charges! 33x19x17, 30 lbs

VIA-Analyzer SWR Meter 5013-1000, with power adapter and serial cord. No manuals or software but works well. Range is 100 kHz to 54 MHz. 3 lbs

Simpson 260-8P Multimeter, in good cosmetic and working condition. Includes two sets of probes, as shown. 10x7x4 (case), 4 lbs

Triplett 630-PLK Type 7 Volt-Ohm-Milliammeter with probes and manual. Please note that the meter requires a 1.5 and 30V battery. We used a D cell, however, no 30V battery was available. All functions and setting appeared to work except the X100 scale for ohms. This, according to the manual, looks like the result of the lack of a 30V battery. 3 lbs

HP 5326A Timer-Counter in overall good cosmetic condition. You will need to supply your own IEC standard power cord. Counts well up to about 50 MHz (rated spec), using input C. No other testing was performed. 4x19x13, 15 lbs

HP 209A Oscillator. Signal generator, attenuator, RMS voltmeter. All appear to work OK, however, switches and controls are dirty and will need cleaning, and unit needs calibration. 8x17x13, 26 lbs

HP 8640B Signal Generator Opt 3 (reverse power protection). This is a 512 MHz unit. Counter is erratic when using the INT/EXT switch...a good cleaning would perhaps reslove this issue. Also, FM modulation/deviation does not work. However, AM signal generator output does work. 5x17x20, 46 lbs

HP 3336B Synthesizer/Level Generator in good cosmetic condition. 75 and 124 ohm outputs installed and in working condition. All functions work well! 6x17x21, 26 lbs

Model Engr. & Mfg. ME-82/U Wattmeter - 50 - 600 MHz, in good cosmetic condition. 146 MHz and 446 MHz agree with bench meter. 7x6x14, 10 lbs

Dentron MT-3000A Antenna Tuner in good cosmetic condition and works well on all bands. 15x14x5, 18 lbs

Heathkit IT-3117 Tube Checker/Tester in overall good cosmetic as well as working condition. Tested with a variety of known good tubes, all OK. 13x11x6, 9 lbs

Beckman Industrial LP10A 17MHz Logic Probe. In original packaging. 1 lb

Seven Collins On/Off Oak Switches, KWM-2. Appear in NOS condition. As shown. 1 lb

Three Late Model K Relays for Collins KWM2-A, all appear unused, NOS. Silver dollar for size comparison only and is not included. 1 lb

Two Collins S-Line RF Transformers, P/N 544-9715-002, appear unused. 1 lb

Collins T8 Audio Output Transformer, P/N 667-0302-00. Appears NOS. Silver dollar for size comparison only and is not included. 1 lb

Five Ohmite 25K Ohm, Wire Wound Fixed Resistors for Collins 516F-2, NOS. 1 lb

Three Adjustable Tuned Input Coils for Collins 30L-1, appear unused, NOS. Specific band(s) unknown, but possibly 20M, based on windings. 1 lb

Four Aemco K4 Relays for Collins KWM2-A, appear unused, NOS. P/N 970-1941-00 1 lb.

(5) Collins Thermal Sensors for 30S-1, appear unused, NOS. 1 lb

Bird Thruline 43 Wattmeter & slugs, as shown. Included are the following: 25W, 200 - 500 MHz 100W, 100 - 250 MHz 250W, 2 - 30 MHz (this element reads about 25% high) Coaxial Dynamics 87004 / 43 dB RF Adjustable Coupler Element (X-Tractor) Blank slug 6x4x3, 5 lbs

BIRD Thruline 43 Wattmeter with add on. See last photo of added circuit board. We could not find any identifying marks on the board to tell us exactly what it is. That being said, there is a switch on circuit board visible through the right side slug holder hole (it's hard to see in the photos). As long as this switch is in the "up" position, the meter works as intended and is accurate with a variety of slugs. You do need to plug the supplied power supply into the circuit board on the left side. We don't know what the switch in the "down" position is supposed to do, however, if it is in this position, the meter needle will peg to the right when any RF is applied. 6x4x3, 5 lbs

Bird Thruline 4230-058 Line Section. Works well! 2 lbs

Coaxial Dynamics 88500-3 RF Line Section w/Type-N Female Connectors. Works well! 2 lbs

Coaxial Dynamics Line Section w/Type-N Female Connectors. Works well! 2 lbs

Three Bird Wattmeter Line Sections, as shown. 6 lbs

Three Bird Wattmeter Line Sections, as shown. 6 lbs

Bird 43 Wattmeter Housing + 2 Line Sections, as shown. Housing is missing back plate. 5 lbs

BIRD Wattmeter Line Section & Meter. Very good condition. All in working condition. 2 lbs

BIRD Wattmeter Line Section & Meter. Very good condition. All in working condition. 2 lbs

Two Panel Meters for a BIRD Wattmeter, in good cosmetic as well as working condition. As shown. (the BIRD meter is still in its plastic protective cover. The other meter is a Phasotron meter, which can be used in BIRD). 2 lbs

General Radio GENRAD 1606B R-F Bridge, in very good condition. Apart from a dirty calibration pot, unit works very well. 10x13x10, 22 lbs

General Radio 1650-B Impedance Bridge in good cosmetic and working condition, surprisingly accurate! 8x13x14, 17 lbs

Racal-Dana 1992 Digital Counter in decent cosmetic condition. Sensitivity about 10.0 uv, all functions and modes work. 4x9x13, 9 lbs

Boonton 26A Millivoltmeter Calibrator in good cosmetic condition. Powered up, produced 1.000 MHz output. Scale and switches appear to work normally. 6x9x12, 10 lbs

Heathkit IP-2717A Regulated Power Supply in good overall cosmetic as well as working condition. Max voltage output is approximately 370V. 13x12x6, 17 lbs

BK Precision 1856B Frequency Counter in good cosmetic condition. Readable display, LCD needs proper lighting, LF & RF inputs count properly. However, RF2 (prescaler) 100-2700 MHz input does not count, just shows random numbers. 4x10x11, 4 lbs

MFJ-842 + Micronta and GC SWR Meters all in working condition. 3 lbs

MFJ-461 Pocket CW Reader. Powers on and displays with a 9v battery (not included). 1 lb

Heathkit Antenna Switch in good working condition, as shown. 1 lb

Lodestar FC-5250C Frequency Counter in good cosmetic condition. Excellent sensitivity up to 178MHz but didn't quite make it to 200 MHz. 2 lbs

Johnson Viking 122 VFO in good cosmetic condition. Output good on all bands, 15V p-p, works well. 8x7x7, 5 lbs

Optoelectronics FC-50C Frequency Counter in good overall condition, as shown. There is a segment out on the first digit. Unit counted to 50 MHz direct, and 350 MHz on pre-scale. Requires 0dBm to +10 dBm signal to count. 2 lbs

West Mountain Radio RIGblaster Advantage, with box. Powers up, but no further testing was done. 2 lbs

West Mountain Radio RIGblaster Advantage, with box. Powers up, but no further testing was done. 2 lbs

West Mountain Radio RIGblaster Plus, new in box, still wrapped, as shown. 4 lbs

RigExpert Standard USB Transceiver Interface in good cosmetic condition. You will need to supply your own USB and other interface cables. 1 lb

West Mountain Radio RIGblaster, appears new. Includes CD and cables, as shown. 2 lbs

West Mountain Radio RIGblaster in box, with accessories as shown. 2 lbs

Chicago Standard P-6415 Isolation Testing Transformer. Tested OK, output voltages are relative to input voltages. Wiring is two conductor with no ground pin. 350VA. 17 lbs

Der EE DE-961TR Multimeter with probes. In good working condition, clean battery case. 1 lb

MFJ-1272BYV Microphone/TNC Switch for K-VHF. Interface with custom audio isolation transformer. Untested. 2 lbs

LP AK-30-TGN RF Connector Adapter Kit 30 Piece Connector Adapter Kit - N / Mini UHF / TNC / BNC / UHF / SMA, as shown.

Nye Viking 52 ohm Low Pass Filter - new in box, + Unmarked Speaker also new in box. Speaker tested OK, low pass filter also tested good but not tested at full power. 2 lbs

Anderson Power Pole + Fuse Kits, all appear new and unused. As shown. 1 lb

Hy-Gain DCU-1 Pathfinder Directional Control Unit. No rotator - unit only. Includes remote data cable, rotator cable. Powers up OK. 9x8x4, 7 lbs

Mirage MP2 VHF Wattmeter in good cosmetic condition. Wattmeter reads slightly high, SWR reads fine. Switches need cleaning. Will require a 9V battery, connections are clean. 2 lbs

Excelvan M6013 Capacitor Meter in very good cosmetic condition and includes original box. Display is sharp. Tested a variety of capacitors and it worked well. Will need two AA batteries. 1 lb

Altelicon ANF-2602 Type N Connectors + Extras including males and more, as shown. 4 lbs

Box of RFS Connector Kits and More, as shown. 14 lbs

25 NIB Andrew L4PNM-RC RingFlare N Male Connectors. Opened several boxes to confirm contents. As shown. 9 lbs

DX Engineering Coax Stripper Set in good condition, as shown. 5 lbs

Transco 11850 RF XMSN Line Switch in good cosmetic and working condition. 1 lb

Two Decibel DB4303B 100 W Dummy Loads and an unmarked smaller load. One of the 100W units test open, other two at 52 ohms. 7 lbs

Dow Key Relay, 12VDC, in good cosmetic and working condition. 1 lb

Three Dow Key Relays, two 12VDC and one 26.5VDC. They are in rough shape, the two 12VDC units work, we were unable to test the 26.5VDC unit. 1 lb

Pyramid PS-14KX Power Supply in good cosmetic and working condition. Tested good to 14 amps (full load). 8x7x5, 10 lbs

Copper Ground Strap, 1/2" and 4 inch widths. As shown. 3.5 lbs

Northern Engineering Labs T-12A, 870 kHz Xtal. Tests spot on at 870 kHz (using pins 3 & 7). These crystals were used in some AM broadcast transmitters. 1 lb

Hand Punch and Case, with punches, as shown. 2x9x5, 3 lbs

Kenwood MC-60 Microphone, in good cosmetic and working condition. 2 lbs

Turner Super Sidekick Microphone, mic element is good, otherwise, untested. 2 lbs

Electro-Voice 205-STC Differential Microphone, in good cosmetic condition; element is good, otherwise, untested. 1 lb

Shure 737A Crystal Microphone, Shows some wear and age but in working condition. 3 lbs

Shure 51S Microphone in decent cosmetic condition. Works but includes head and stand only, no cord. 2 lbs

1940's Turner CX "Repoter" Crystal Microphone for restoration. For restoration, this mic is non-functional. 2 lbs

Lot of 9 Miscellaneous Microphones, including: D-104 head w/broken connector Calrad DM-15 head, tests OK Unmarked black mic w/stand, unable to test Electrovoice 605, tests OK Turner model unknown, tests OK Calrad D-600 head only tests OK Electrovoice head and cable, non-working Brown mic/stand no markings, non-working Gray mic/stand w/gooseneck, tests OK 13 lbs

Heil Headphone & Boom Mic, in working condition, ear pads are flaking. No model number markings can be found anywhere on the headphones or element. 2 lbs

Heil Pro-Set Plus Headphones + Boom Mic, with boom mic, in good working condition. 2 lbs

Heil Pro-Set Plus! Headphones + Boom Mic. Tested OK and in very good condition. 3 lbs

Two Pairs of Heil Headphones with boom mics. One needs replacement ear fitting. Both are functional. 2 lbs

Heil HM-10 Microphone & Boom w/Yaesu adapter, all in good cosmetic and working condition. 6 lbs

Heil Goldline Microphone & Boom in good cosmetic condition. We're not sure which Heil adapter is being used or if it's a Heil. You may need to supply a known Heil adapter to use this mic. 5 lbs

Three Heil Adapter Cables for Yaesu, two AD-1-Y and a CC-1-Y, as shown, in original sealed plastic bags. 2 lbs

Four Hi-Impedence Mics, appear new in box. Very nice. No identifying marks, other than what is shown. Silver dollar is for size comparison only and not included. 1 lb

Four Hi-Impedence Mics, appear new in box. Very nice. No identifying marks, other than what is shown. Silver dollar is for size comparison only, and not included. 1 lb

LOT of Microphones & Parts, as shown. 5 lbs

Clipper 632-S Foot Switch, appears very lightly used, if at all. 3 lbs

WER Straight Key, 1939, in good working condition, as shown. 2 lbs

Vibroplex Original Standard Bug, good working condition, contacts need adjustment. SN 243547 3 lbs

Teardrop Straight Key, in good working condition. 1 lb

Unmarked Straight Key in good cosmetic and working condition. 1 lb

Electric Specialty Bug, as shown. 2 lbs

Speed-X Straight Key, excellent condition, as shown with box. 1 lb

Electro Mfg. Co. Model 11 Paddle 2 lbs

Chinese D-118 Straight Key + Original Box, as shown. 3 lbs

Chinese DK-741 Straight Key + Box, appears unused, as shown. 2 lbs

Unmarked Bug Paddle. Size is similar to standard Vibroplex, but no other markings were found. Thumb paddle is not attached. 2 lbs

Telegraph Keys and Bug Parts, as shown. 9 lbs

Two RF Parts 3-500ZG Tubes + Boxes. Tests 70-75% and 75-80%, no shorts or gas, using our in house text fixture. NOTE: these tubes were not tested at RF frequencies, but they are safe to use in your amplifier. 2 lbs

Two Eimac 3-500Z Tubes + Boxes, tested 85-90% and 70-75%, no shorts or gas, using our in house text fixture. NOTE: these tubes were not tested at RF frequencies, but they are safe to use in your amplifier. 2 lbs

Two 3-500Z Tube Chimneys, as shown. 2 lbs

Eimac 4-400C Tubes + Boxes. Tubes are used, and filaments are good, but no further testing was performed. 2 lbs

Three Eimac JAN- 8860 Tubes. Two of the tubes appear to be NOS but can not verify. All tubes have good filaments, but no further testing was performed. 8 lbs

Two Eimac JAN-8860/4CX1500B Tubes with boxes. tubes appear to be NOS, but can not verify. Filaments are good, but no further testing was performed. 3 lbs

Three 8168/4CX1000A Tubes, all used with good filaments, but no further testing was performed. 6 lbs total

Two Eimac 8877/3CX1500A7 Tubes, one appears to be NOS, but not verified. Both filaments are good, but no further testing was performed. 3 lbs

Eimac 8877/3CX1500A7 and box. Tube appears to be NOS, but not verified. Filament is good, but no further testing was performed. 10x6x6, 2 lbs

Eimac 8877/3CX1500A7 tube and box. Appears to be NOS, but not verified. Filament is good, no further testing was performed. 10x6x6, 2 lbs

Eimac 8877 tube and box. Used tube, filament tests good, no further testing performed. 10x6x6, 2 lbs

Varian 3-1000H Tube + Eimac SK-516 Chimney. Filament tests good on tube, but no further testing was performed. 3 lbs

Four Raytheon 4D32 Tubes, NOS, unopened. Date on box is 1977. 3 lbs

Two Eimac 4E27A/5-125B Tubes. Filaments are good, but no further testing was performed. 2 lbs

Two Amprex 813 Tubes. Filaments test good, but no further testing was performed. 2 lbs

Tube Lot, two 7203, a 5894, 4CX250B, and 3CX800A7 with no box. All tubes have good filaments, but no additional testing was performed. 4 lbs

Jennings UCS Vacuum Variable Capacitor, 7500 volt, Capacitance does vary, as expected, but Hi-Pot testing was not performed. No other markings found on unit. 2 lbs

Jennings UCSL-2000-5S Vacuum Variable Capacitor. Capacitance does vary, as expected, but Hi-Pot testing was not performed. 2 lbs

Jennings 375 Vacuum Variable Capacitor. Capacitance does vary, as expected, but Hi-Pot testing was not performed. 2 lbs

Two Alliance Mfg Co Rotors, as shown. May be incomplete. 20 lbs

Alliance Mfg Co Model 73 Rotor and Parts, as shown. 15 lbs total

Tailtwister T2X Rotor, 1984. Untested. 15x10, 35 lbs

Prop Pitch Motor. No visible markings. Nor do we know if it's been modified for rotor service. Untested, as shown. 50 lbs

Prop Pitch Motor. No visible markings. Nor do we know if it's been modified for rotor service. Untested, as shown. 50 lbs

Prop Pitch Motor. No visible markings. Nor do we know if it's been modified for rotor service. Untested, as shown. 50 lbs

M2 Antenna Systems RC2800P-A Control Unit. Display is bright and sharp. Pressing buttons did change display accordingly, but no other testing was performed. 6x9x9, 13 lbs

M2 Antenna Systems RC2800PX Control Unit. Display is bright and sharp. Pressing buttons did change display accordingly, but no other testing was performed. 6x9x9, 13 lbs

Radio Shack Discone Base Station Antenna, new old stock in package, as shown. 3 lbs

Collins Transmitters Catalog, Bulletin 100. In good overall condition, as shown. 1 lb

LOT Palomar Ferrite Beads, as shown. Dollar coin for size comparison only. Appears unused. 2 lbs

LOT of Baluns, RF transformers and related parts, as shown. 3 lbs

Various Hustler Antenna Parts/Traps, including a Hustler Super RM-80-S and a trap marked 30M. There are no other identifying marks on this antenna(s). Being sold as parts.

Unmarked M2 Antenna, as shown. There are no identifying marks on the inside of this box. The only reason we are mentioning M2 is that the UPS label is from M2 antennas. We also don't know if this is a complete unit, however, the box was unopened when received. 50 lbs

Collins 32S-1 Transmitter, WE, in good cosmetic condition. Has carrier oscillator issues with TX output on some bands but intermittent and not stable. Will not key in CW mode. SN 10462 15x12x8, 17 lbs

Collins 32S-1 Transmitter, WE, in good cosmetic condition. Filaments do not light but draws high DC power at power on. Needs some troubleshooting and TLC. SN 1210 15x12x8, 17 lbs

Collins 75S-1 Receiver, WE, in good cosmetic condition, noting slight misshapen hinged top. No power cord. All controls noisy, needs troubleshooting, alignment and general TLC. Has noise but no RX. Rejection tuning seems to work, RF gain control seems to be controlled reverse of what it should be. SN 1167 15x13x8, 18 lbs

Collins 30L-1 Linear Amplifier, for repair, WE, no cabinet as shown. Inoperable. Suspect antenna relay changeover circuit. 8x15x14, 39 lbs

Heathkit HW-8 CW Transceiver & HWA-7-1 Power Supply. TX power output ranges from 1.5W to 2W, however, there is no RX noise heard. The audio amp does work, however. 5x10x9, 4 lbs 3x4x5, 3 lbs

Advanced Receiver Research P432VDG Preamp, needs work - no gain, amp non-functional. 1 lb

(4) 28" Andrew LDF4-50A 1/2" Heliax Patch Cables with "N" connectors. 28 inches each, 5 lbs total

Kenwood TS-940 Transceiver, parts/repair. As you can see from the photos, this radio was damaged in that the right rear corner (looking at it from the back) was pushed in, probably from dropping it on that side. This being said, the unit does power on, S-meter moves smoothly, and display is good. The controls will need cleaning as they are dirty/noisy. TX/RX are both very weak. RX sensitivity is 2.0 uv on all bands and power output ranges from 15W to 35W, depending on band. SN 5120826 17x16x6, 45 lbs

Kenwood TS-830S Transceiver in overall good cosmetic condition, however, this unit does have display issues (which are well documented online). Basically, the VFO does not track with the operating frequency display. The display is sharp/bright. RX sensitivity is 0.2 uv on all bands, and TX power output ranges from 60W to 100W depending on band. SN 1092160 15x14x7, 29 lbs

Icom MB-65 Mounts in good condition, as shown. 1 lb

Sony ICF-SW55 Stereo PLL Synthesized Receiver and case. Initially powers up and receives some AM/FM stations. Time/date does not hold. Powers off automatically. Needs some work. 11x12x3, 4 lbs

Icom IC-2AT Transceiver + accessories. Includes hand mic, battery is dead. Switches on top work, TX output 2W and 5W, RX sensitivity 0.2uv. 2 lbs

Icom IC-T81A VHF/UHF 1.2 GHz HT Transceiver, antenna and manual. BC-110A wall wart charger included, but not shown. NOTE: The battery will not hold a charge and will need to be replaced. Frequency coverage: TX: 50-54 / 144-148 / 430-450 / 1240-1300 MHz RX: 50-999 / 1240-1300 MHz (cellular blocked) TX power output is only 1W (on high) for 2M, 440MHz. 0.25W on 6M and slightly over 1W on 1.2 GHz. RX sensitivity is 0.5 uv +/- on all bands. These values were observed using only the wall charger plugged into the rig. 2 lbs

The Fisher CA-40 Mono Integrated Amplifier. There are some cracks in the front upper right corner of the unit as shown. Also, the internal fuse blows upon power up. This unit is being sold for parts/repair. 6x13x10, 23 lbs

Tracor 599K VLF/LF Receiver needs some TLC. Strip chart ticks and writes, but no needle movement, carrier and sync lamps illuminate and the meter moves. No docs or power cord. 7x19x19, 40 lbs

Wiltek 108 Antenna Multicoupler in good cosmetic condition. No power cord, unable to test. 6x11x16, 10 lbs

HP 5087A Distribution Amplifier inoperative. May be a power supply issue. 4x19x13, 15 lbs

HP 105B Quartz Oscillator in good cosmetic condition. Warms up normally but has functionality issues and output is not usable. 4x19x13, 10 lbs

Tripp Lite PR-7b Power Supply in good cosmetic and working condition. 6 lbs

Radio Shack 3 Amp Power Supply in good cosmetic and working condition. As shown. 4 lbs

HAL DXP38 Modem for RTTY and Clover II. Can apparently be used for PACTOR as well. Untested. You will need your own power supply. As shown. 4x8x11, 3 lbs

Tempo Research AEA HF Analyst and manual. Initially powers up but display has a "washed out" appearance and is unreadable. Includes software disc. You'll need to supply a power source. Being sold for parts/repair. 3 lbs

Comet CMX-3 All Time Multi Media Monitor (SWR/Power Meter) appears lightly used, but it is missing the CMX-3RS RF sensor. 1 lb

Sony Pyxis Global Positioning System. Does not power up with battery or power supply. Being sold for parts or repair. 2 lbs

Kikusui COS6100 Oscilloscope. This unit has no trace and will need repair. 7x15x19, 22 lbs

RCA Microphone in pretty rough condition, being sold for parts. 2 lbs

Unmarked Tuning Capacitor in good cosmetic condition, untested. 1 lb